Comments on: ASME Codes and Standards – A summary https://www.weldingandndt.com/asme-codes-and-standards-a-summary/ Thu, 01 Apr 2021 11:59:10 +0000 hourly 1 https://wordpress.org/?v=7.0 By: Keelara veeregowda chandramouli https://www.weldingandndt.com/asme-codes-and-standards-a-summary/#comment-232 Mon, 04 Mar 2019 09:15:32 +0000 http://www.weldingandndt.com/?p=409#comment-232 Dear Sri.Sandeep Anand
Highly informative to cadet engineers who have come out from Technical Almater.Keep educating your Fraternity.

]]> By: Saurabh joshi https://www.weldingandndt.com/asme-codes-and-standards-a-summary/#comment-210 Wed, 26 Dec 2018 05:48:38 +0000 http://www.weldingandndt.com/?p=409#comment-210 Quite Informative and interesting.

]]> By: Ramesh Krishna https://www.weldingandndt.com/asme-codes-and-standards-a-summary/#comment-183 Sat, 29 Sep 2018 06:35:37 +0000 http://www.weldingandndt.com/?p=409#comment-183 In reply to Rohit Rakesh A.

Hi rohit,
The Pressure vessel tolerance were made based on the dimensional change which will effect Integrity of the vessel. Example Out of roundness of shell UG-80, Tolerance for Formed Heads UG-81, Other Tolerance as per UG-16 of ASME Sec VIII div-1,
Material tolerance as per Material specification, Refer ASME Sec II A.

]]> By: Ramesh Krishna https://www.weldingandndt.com/asme-codes-and-standards-a-summary/#comment-182 Sat, 29 Sep 2018 06:24:41 +0000 http://www.weldingandndt.com/?p=409#comment-182 In reply to Rohit Rakesh A.

Hi Rohit Rakesh,

Go through UG-99 of ASME Sec VIII div 1,Gage selection as per UG-102, If your conducting test for vessel 1.1 times MAWP multiplied by LSR (see the code). If you are conducting the test for RF pads normally conducted at low pressure 1 bar or less to ensure weld tightness that seal off the inside of vessel. Refer UG-37 of ASME Sec VIII div-1 2013 edition. It has been removed in 2015 code.

]]> By: Avadhut Kulkarni https://www.weldingandndt.com/asme-codes-and-standards-a-summary/#comment-173 Mon, 10 Sep 2018 16:43:17 +0000 http://www.weldingandndt.com/?p=409#comment-173 Dear Sir,
Very Useful Article.
However I want you to write articles & make more videos on the Following topics;
1. PWHT
2. Impact Test requirements as per ASME Sec 8 Div 1
3. Welding Metallurgy
4. PED standard for Pressure vessels
5. Stage Inspection procedures for pressure vessels

]]> By: ALOK SINGH https://www.weldingandndt.com/asme-codes-and-standards-a-summary/#comment-171 Mon, 03 Sep 2018 03:36:35 +0000 http://www.weldingandndt.com/?p=409#comment-171 good source of information

]]> By: Rohit Rakesh A https://www.weldingandndt.com/asme-codes-and-standards-a-summary/#comment-167 Sat, 11 Aug 2018 16:09:21 +0000 http://www.weldingandndt.com/?p=409#comment-167 Hello sir,
please help sir pressure vessel for tolerance allowance, pneumatic test procedure, and gauge selection.

]]> By: Rohit Rakesh A https://www.weldingandndt.com/asme-codes-and-standards-a-summary/#comment-166 Sat, 11 Aug 2018 16:04:17 +0000 http://www.weldingandndt.com/?p=409#comment-166 Hello Sir,
please send pressure vessel for pneumatic test procedure , gauge selection and pressure vessel tolerance allowance book please help

]]> By: MARCELO JUAN LOPEZ https://www.weldingandndt.com/asme-codes-and-standards-a-summary/#comment-142 Sun, 10 Jun 2018 18:58:28 +0000 http://www.weldingandndt.com/?p=409#comment-142 Muy buena vuestra información, muchas gracias.

]]>